Roller guides: runner profiles, bearing units and rollers D14
I-type profiles
Profiles 5
Profiles 6
Profiles 8
Profiles 8X
Profiles 8-30
Profiles 10
Profiles 12
Bearing Unit 8 D14 e
Linear slides are built up with bearing units. They are used in pairs, 1 piece eccentrically (this is set backlash-free) and opposite 1 piece centrically. To minimise wear, a wiper lubrication system must always be installed on each bearing unit.
Bearing Unit 8 D14 z
Linear slides are built up with bearing units. They are used in pairs, 1 piece eccentrically (this is set backlash-free) and opposite 1 piece centrically. To minimise wear, a wiper lubrication system must always be installed on each bearing unit.
Bolt 8 D14 e, bright zinc-plated
Bolt for fixing and adjusting the track roller D14 on the eccentric side.
Bolt 8 D14 z, bright zinc-plated
Bolt for fastening the track roller D14 on the centric side.
Double-Bearing Unit 8 D14 e
Linear slides are built with storage units. They are used in pairs, 1 each eccentric (this is set free of play) and opposite 1 centric. In order to minimize wear, a wiper lubrication system must be installed on every bearing unit.
Double-Bearing Unit 8 D14 e, stainless
Linear slides are built with storage units. They are used in pairs, 1 each eccentric (this is set free of play) and opposite 1 centric. In order to minimize wear, a wiper lubrication system must be installed on every bearing unit.
Double-Bearing Unit 8 D14 z
Linear slides are built with storage units. They are used in pairs, 1 each eccentric (this is set free of play) and opposite 1 centric. In order to minimize wear, a wiper lubrication system must be installed on every bearing unit.
Double-Bearing Unit 8 D14 z, stainless
Linear slides are built with storage units. They are used in pairs, 1 each eccentric (this is set free of play) and opposite 1 centric. In order to minimize wear, a wiper lubrication system must be installed on every bearing unit.
End Cap and Lubricating System 8 D14, black
To minimise wear, a wiper lubrication system should always be fitted to each bearing unit.
Roller D14, stainless
Precision roller for use in the bearing units 8.
Roller Profile 8 D14, natural
The track roller profile is used to create bearing units D14 in suitable length up to 6000mm. Cut to size max. 6000 mmCompatible with item 0.0.426.02
Roller Profile 8 D14, natural
The track roller profile is used to create bearing units D14 in suitable length up to 6000mm. Cut to size max. 6000 mmCompatible with item 0.0.426.02
Shaft clamp Profile 8 D14, natural
The shaft clamping profile is used to hold the guide shaft d14. The shaft is pressed into the profile groove by pressing in the shaft clamping profile. The shafts are secured by a DIN6325 cylindrical pin.
Shaft clamp profile D10, natural-8
The shaft clamping profile is used to hold the guide shaft d10. The shaft is pressed into the profile groove by pressing in the shaft clamping profile. The shafts are secured by a DIN6325 cylindrical pin. Compatible with item 0.0.442.03
Shaft clamp profile D25, natural-8
The shaft clamp profile is used to hold the guide shaft d25. The shaft clamp profile is screwed on with S1397 countersunk screws M6x16 DIN 7991 and NI-1040 slot nuts M6, galvanised-8. The holes for the screw connection are 200 mm apart. Compatible with item 0.0.350.02
Timing Belt R25 T10, black
For creating highly dynamic linear drives with toothed belt drive.
Timing-Belt Reverse Unit 8 80 R25 with Bore
For creating highly dynamic linear drives with toothed belt drive. Compatible with item 0.0.366.07
Timing-Belt Reverse Unit 8 80 R25 with Bore
For creating highly dynamic linear drives with toothed belt drive.
Technische Daten
Gilt für alle Profile dieser Baureihe. Abweichungen einzelner Varianten stehen auf der jeweiligen Produktseite.
Item kompatibel
| Slot pull-out force | F=5.000 N |
|---|---|
| Material | Al Mg Si 0.5 F25, artificially aged |
| Surface | natural anodised E6/EV1 |
| Tolerances | to EN 12020-2 |
| Supply form | Bars up to 6,000 mm, cut to the millimetre |
| Compatible with | Item |
Verfügbare Querschnitte
Alle Varianten dieser Baureihe auf einen Blick — Querschnitt, Nutenausführung, Bauart und Nutauszugskraft je Profil.
Systemkompatibilität
Was zur Roller guide profiles passt – und was nicht. Der Zusatz „kompatibel" bleibt bewusst: Item ist eine fremde Marke, wir führen kein Originalteil.
Was passt
- The complete slot 8 accessory range for mounting to structures of series 8
- Bearing units and double bearing units 8 D14 in eccentric and concentric versions, also stainless
- Wiper and lubrication system 8 D14 for dusty and continuously running applications
- Timing belts R25 T10 and timing belt idlers 8 80 R25 for the drive
- Load-bearing structure to match: aluminium profiles slot 8 in grid 40
- The closed alternative: C-rails and C-profiles
Was nicht passt
- Rollers D14 on a runner profile 8 D10 – roller diameter and profile have to match
- Bearing units from the C-rail on open runner profiles – different guide geometry
- T-slot nuts for slot 5, 6, 10 and 12 – different slot geometry
Maßlich kompatibel zu Item Roller guide profiles. Kein Originalteil von Item, keine Vertriebs- oder Lizenzbeziehung. Profile mit anderer Nutbreite sind nicht kompatibel.
Anwendungsbeispiele
Item-kompatible Profile im Einsatz
Linear axes in special machinery
Handling axes and infeeds with belt drive – considerably cheaper than recirculating ball guides.Gantries and travel axes
Travelling gantry axes above working areas, combined with profiles of series 8.Heavy sliding gates and doors
Large sliding elements where the C-rail reaches its load limit.Test and measuring fixtures
Travelling mounts for test heads and sensors with a reproducible position.Item Profile: häufig gestellte Fragen und Antworten
Hier finden Sie Antworten auf die häufigsten Fragen zu unseren Item kompatiblen Aluprofilen. Von der Maßgleichheit über die richtige Nutbreite bis zu Material und Zuschnitt.
Bleibt eine Frage offen, hilft Ihnen unser Team persönlich weiter. Sie erreichen uns Mo. bis Fr. von 9 bis 17 Uhr unter 09452 9334-0.
What is the difference from the C-rail?
Which roller fits which profile?
Can the guide be driven?
Need help putting your setup together?
We are happy to help.
Our team advises you personally on selecting and combining your profiles and components – from the first idea to the finished construction.
(Mon – Fri 9am–5pm)